1770 x 320px
Products
.370 Manual Straight Fluted Reamer
Add to Compare
$58.80
These manual Spiral fluted reamers are excellent for finishing and reconditioning hosel bores to a high degree of accuracy and surface finish.
A190010-370
CLUBMAKING
Golf Mechanix
These manual Spiral fluted reamers are excellent for finishing and reconditioning hosel bores to a high degree of accuracy and surface finish.
Title
*
Sold out
.410 Clubhead Setup Shaft to Head Connector for R&A/USGA Test Pendulum
Add to Compare
$144.00
Designed for speed and convenience for either production or lab use, this setup shaft to head connector allow operators to test several clubheads of the same design, eliminating the nee to re-adjust the back clamp each time a new head...
A070600-A410
CLUBMAKING
Golf Mechanix
Designed for speed and convenience for either production or lab use, this setup shaft to head connector allow operators to test several...
Title
*
12 Inch Classic Blade Style Grip Remover
Add to Compare
$52.80
Designed as an alternative to using solvents or compressed air, the Classic Blade Grip Remover allows club-makers to reuse rubber or composition grips.The classic blade grip remover features a channel to funnel solvent under the grip to loosen the tape....
A110800-12
Golf Mechanix
Designed as an alternative to using solvents or compressed air, the Classic Blade Grip Remover allows club-makers to reuse rubber or composition...
Size
*
ASP-G0401-48X1X080
CLUBMAKING
Golf Mechanix
Shafting Supplies
Grit
*
20 Inch Classic Blade Style Grip Remover
Add to Compare
$97.20
Developed as a safe alternative over pressurized solvent ?grip shooters? and compressed air, the Classic Blade Grip Remover allows club-makers to re-use rubber or composition grips when counter-weighing, butt trimming, extending, or swing weighing golf clubs. Made of cold rolled...
A110800-20
CLUBMAKING
Golf Mechanix
Developed as a safe alternative over pressurized solvent ?grip shooters? and compressed air, the Classic Blade Grip Remover allows club-makers to re-use...
Title
*
20 Inch Long Spring Rod Grip Remover for Round Putter Grips
Add to Compare
$101.40
The Spring Rod Grip remover distinguishes itself from the blade style grip remover by its flexibility and edge to edge progressive dual lifting action. Twisting and shoving the rod with a slight solvent dip will help remove the grip with...
A110810-20
CLUBMAKING
Golf Mechanix
The Spring Rod Grip remover distinguishes itself from the blade style grip remover by its flexibility and edge to edge progressive dual...
Title
*
Sold out
24 HOUR SHAFTING EPOXY KIT - 16OZ
Add to Compare
$80.00
The Dynacraft high strength epoxy is specially formulated for clubmakers with both high shear and torsional strength. Easy to use - mixes 1:1 by volume, dries ivory, sets in 3 hours and full cure in 24 hours.
ACM059
The Dynacraft high strength epoxy is specially formulated for clubmakers with both high shear and torsional strength. Easy to use - mixes...
Title
*
Sold out
ASP-N0201-01
CLUBMAKING
Golf Mechanix
3 Point cutting blade.
Title
*
Sold out
3/4" Jaw Set for Hickory Shafted Clubs
Add to Compare
$80.40
3/4" Jaw Set for Hickory Shafted Clubs.
A150614-SK12
CLUBMAKING
Golf Mechanix
3/4" Jaw Set for Hickory Shafted Clubs.
Title
*
Sold out
ASP-Q0603-01-P6
CLUBMAKING
Golf Mechanix
Pack of 6
Title
*
Sold out
ASP-Q0603-04-P3
CLUBMAKING
Golf Mechanix
Pack of 3.
Title
*
DP81048ML
CLUBMAKING
Epoxy Supplies
Title
*
48 Inch Long Drill Set for Steel (7/32) and Graphite (5/32) Shafts
Add to Compare
$144.60
Each re-sharpenable, high-quality HSS bit is brazed to a Stiff stainless steel shank and trued to prevent wobbling and flexing too much while peck drilling. Peck drilling prolongs tool life by breaking up chips and reducing heat buildup to prevent...
A190600
CLUBMAKING
Golf Mechanix
Each re-sharpenable, high-quality HSS bit is brazed to a Stiff stainless steel shank and trued to prevent wobbling and flexing too much...
Title
*
48 Inch Ram-Rod for Steel and Graphite Shafts (full set)
Add to Compare
$45.00
The main usage of this Ram-Rod, however, is as a heat rod for indirectly heating the epoxy of a club-head, which is useful when the club-head should not be exposed to direct heat. Made of hardened spring steel, the rod...
A190400
CLUBMAKING
Golf Mechanix
The main usage of this Ram-Rod, however, is as a heat rod for indirectly heating the epoxy of a club-head, which is...
Title
*
5/32 48 Inch Long Drill Bit for Graphite Shafts
Add to Compare
$89.40
A ?must have? 48 inch drill bit set for making swing weight adjustments on fully assembled clubs - steel or graphite shafted.These drill bits are perfect for clearing out shaft tips, coring out excess epoxy glue, loosening weights and lightening...
A190600-396
CLUBMAKING
Golf Mechanix
A ?must have? 48 inch drill bit set for making swing weight adjustments on fully assembled clubs - steel or graphite shafted.These...
Title
*
Sold out
5G Stick On Lead Swing Weight Patch (20 sticks)
Add to Compare
$29.40
Stick on 5 gram lead patches used for altering swing weight, MOI as well as ball flight trajectory. Used during fitting sessions, these patches are stackable and can be easily removed without damaging the club-head finish.
ASP22LSWP
CLUBMAKING
Golf Mechanix
Stick on 5 gram lead patches used for altering swing weight, MOI as well as ball flight trajectory. Used during fitting sessions,...
Title
*